||Você não está logado !
Acessar sua Conta ou Registrar-se?
Fazer downloads não requer logon.
Abit IS7-E Bios 13
Avaliação Média: 0%
- de Usuário: 0 votos
- de Visitantes: 134 votos
56K: 53s 64K: 46s 128K: 23s 768K: 3s
Total: 38 | Última semana: 0
Win Vista, Win2000, Win2003, Win2008, Win95, Win98, WinME, WinNT, WinXP X64
Abit IS7-E Bios 13 Descrição do Produto:
# New Fixes/FeaturesAdded support for IS7-G, IS7, and IS7-E.
# Updated CPU micro code (CPU: 0F29H, ID=11H).
# Updated CPU micro code (CPU: 0F29H, ID=11H).
# Added CPU multiplier 8X for engineering sample CPU and maximum CPU frequency 412MHz.
# Revised setup menu for OnChip Serial ATA.
# Fixed on-chip SATA boot issue while another bootable hard drives exist and attached to IDE-1 or IDE-2.
# Updated memory reference code and ICH5 BIOS spec to v1.2.
# Fixed PS/2 mouse malfunctioning problem while the USB cable of Media XP attached to mainboard.
# Fixed DOS 6.22 booting failure from FAT16 partition.
# Fixed BIOS hang-up problem which is caused by specific CPU cooling fan reporting error RPM to BIOS when CPU FanEQ 60% enabled.
# Revised the following default settings in BIOS setup page. - Bootable Add-in Device: PCI Slot Device - CPU FanEQ Active Temperature: 70 C - CPU Warning Temperature: 85 C
# Added 80, 85, and 90 degrees C into "Shutdown Temperature".
# Enabled "IDE Block Mode" and hided the option.
# Revised ICH5R RAID BIOS display issue.
# Revised power-on delay time from 4~5 seconds to 1~2 seconds after AC power lost and resumed.
# Added description for "Bootable Add-in Device".
# Fixed the problem that NB fan still reports full speed in PC Health page when "CPU FanEQ Speed Control" is enabled.
# Added new option "IDE Bus Master".
# Added description for "Shutdown when CPUFAN Fail".
# Revised the wording of IDE channels inside the BIOS Setup. IDE Channel 0, 1, 2, and 3 are changed to 1, 2, 3, and 4.
# Added new option "SATA RAID ROM" to setup both "OnBoard SATA" and "OnChip SATA".
# Added new option "HDD Change Message" in Advanced BIOS Features and the default setting is "Disabled". If this option is changed to "Enabled",the system will show warning message and prompt for a confirmation whenone or more than one HDD had been added into or removed from the system.
# Fixed "CPU THRM-Throttling" function.
# Added new options "Refresh Cycle Time", "Read Delay Adjust (tRD Adj)", and "Command Per Clock (CPC)".
# Changed the default setting of "Drive A" from "None" to "1.44M" after Load Fail-safe Defaults.
# Changed the default setting of "OnCip Serial ATA" to "Auto".
# Added "Game Accelerator" technology.
# Revised the error reading of fan speed for specific CPU cooling fan when FanEQ 60% enabled.
# Fixed the slow detection problem when HDD simulation card installed.
# Fixed the problem that SMARTDRV.EXE malfunction in DOS 6.22 environment.
# Fixed the problem that Windows 98 bootable floppy disk causes system hang up during loading CD-ROM driver when "OnChip Serial ATA" is set to"Auto" or "Enhanced Mode".
# Removed the option "Force Update ESCD".
# BIOS Compile Date: 6/10/2003.
For those without the need for onboard RAID or Firewire, but the need to keep costs down, the IS7-E is the board to get. Like the other boards in the IS7 series it uses the tried and true Intel tested Springdale-PE chipset for Hyper-Threading Pentium 4 processors. It comes with, Dual DDR 400, AGP 8X, and softmenu Technology. This board makes for an affordable, super-stable system.
Enhanced 800MHz FSB
The 800MHz FSB increases bandwidth and improves overall system performance.
Serial ATA 150MB/s data transfer rate
Serial ATA is an evolutionary replacement for the Parallel ATA storage interface. This new high-speed interface boosts data transfer rates to up to 150 MB/sec. More flexible power tolerances allow for smaller and more efficient cables.
6-Channel Audio and S/PDIF Out interface
Lets you enjoy 6-channel audio without having to buy advanced sound cards.
USB 2.0 Supports 480MB/s data transfer rate
Supports speeds up to 480 Mb/sec, approximately forty times faster than conventional USB 1.1
ABIT SoftMenu Overclocking
The overclocking function includes CPU frequency, multiplier, CPU Vcore, memory voltage and AGP voltage adjustment available to maximize your system performance.
It is highly recommended to always use the most recent driver version available.
Do not forget to check with our site as often as possible in order to stay updated on the latest drivers, software and games.
Try to set a system restore point before installing a device driver. This will help if you installed a wrong driver. Problems can arise when your hardware device is too old or not supported any longer.
Requerimentos de Sistema:Não há requerimentos especiais.
Status da Versão do Programa:
Suporte à Instalação do Programa:
Abit IS7-E Bios 13 Softwares relacionados baixados:
Abit IS7-E Bios 13 :
Abit Motherboards Abit IS7-E Bios Update Abit Motherboard IS7-E bios updated added revised setup onchip serial fixed sata bootable faneq enabled default device temperature